International Journal of Engineering

International Journal of Engineering

Microstructural and Mechanical Characteristics of AlCoCrFeNi-YSZ High Entropy Alloy Matrix Composite

Document Type : Original Article

Authors
M. Askarzadeh Ardestani 1
M. Farvizi 2
A. Alizadeh Samiyan 1
M. Ghanbariha 1
T. Ebadzadeh 1
M. M. Kalantarian 1
1 Department of Ceramic, Materials and Energy Research Center, Karaj, Iran
2 Department of Materials Engineering, University of Tabriz, Tabriz, Iran
10.5829/ije.2026.39.10a.01
Abstract
In this study, high-entropy alloy matrix composites (HEAMCs) consisting of an AlCoCrFeNi matrix reinforced with zirconia-based particles were fabricated using mechanical alloying (MA) followed by spark plasma sintering (SPS). Microstructural analysis revealed the presence of both FCC and BCC phases after 30 hours of mechanical alloying and subsequent sintering at 1000 °C. Rietveld refinement analysis indicated that the weight fraction of the FCC phase remained nearly constant in both the HEA and HEA–YSZ composites. However, the addition of YSZ particles decreased the BCC phase content and restricted grain growth during sintering. Compressive test results showed that the specimen containing 5 wt.% YSZ exhibited the highest yield strength (1760 MPa), attributed to its higher BCC phase fraction (40%). In contrast, the specimen with 10 wt.% YSZ demonstrated reduced yield strength due to a lower BCC phase content (36%). These findings indicate that AlCoCrFeNi composites reinforced with YSZ possess higher yield strength than those reinforced with ZrO₂ when comparable reinforcement levels are used. This improvement is attributed to the higher BCC phase content and the superior intrinsic properties of YSZ. Fracture surface analysis confirmed the coexistence of both ductile and brittle fracture modes in the tested specimens.

Graphical Abstract

Microstructural and Mechanical Characteristics of AlCoCrFeNi-YSZ High Entropy Alloy Matrix Composite
Keywords
High Entropy Alloy Ceramic ParticulatesComposite MaterialsMechanical Properties

Subjects

1.    Yeh JW, Chen SK, Lin SJ, Gan JY, Chin TS, Shun TT, et al. Nanostructured high‐entropy alloys with multiple principal elements: novel alloy design concepts and outcomes. Advanced engineering materials. 2004;6(5):299-303.  https://doi.org/10.1002/adem.200300567
2.    Cantor B, Chang IT, Knight P, Vincent A. Microstructural development in equiatomic multicomponent alloys. Materials Science and Engineering: A. 2004;375:213-8.  https://doi.org/10.1016/j.msea.2003.10.257
3.    Chen J, Zhou X, Wang W, Liu B, Lv Y, Yang W, et al. A review on fundamental of high entropy alloys with promising high–temperature properties. Journal of Alloys and Compounds. 2018;760:15-30.  https://doi.org/10.1016/j.jallcom.2018.05.067
4.    Ye Y, Wang Q, Lu J, Liu C, Yang Y. High-entropy alloy: challenges and prospects. Materials Today. 2016;19(6):349-62.  https://doi.org/10.1016/j.mattod.2015.11.026
5.    Wang F, Zhang Y, Chen G, Davies H. Cooling rate and size effect on the microstructure and mechanical properties of AlCoCrFeNi high entropy alloy. 2009. https://doi.org/10.1115/1.3120387
6.    Zhang Y, Zuo TT, Tang Z, Gao MC, Dahmen KA, Liaw PK, et al. Microstructures and properties of high-entropy alloys. Progress in materials science. 2014;61:1-93.  https://doi.org/10.1016/j.pmatsci.2013.10.001
7.    Chikumba S, Rao VV, editors. High entropy alloys: development and applications. Proceedings of the 7th International Conference on Latest Trends in Engineering & Technology (ICLTET’2015); 2015. 
8.    Miracle DB, Senkov ON. A critical review of high entropy alloys and related concepts. Acta materialia. 2017;122:448-511.  https://doi.org/10.1016/j.actamat.2016.08.081
9.    Ren B, Liu Z, Li D, Shi L, Cai B, Wang M. Effect of elemental interaction on microstructure of CuCrFeNiMn high entropy alloy system. Journal of Alloys and Compounds. 2010;493(1-2):148-53.  https://doi.org/10.1016/j.jallcom.2009.12.183
10.    Ji W, Fu Z, Wang W, Wang H, Zhang J, Wang Y, et al. Mechanical alloying synthesis and spark plasma sintering consolidation of CoCrFeNiAl high-entropy alloy. Journal of Alloys and Compounds. 2014;589:61-6.  https://doi.org/10.1016/j.jallcom.2013.11.146
11.    Zhang A, Han J, Meng J, Su B, Li P. Rapid preparation of AlCoCrFeNi high entropy alloy by spark plasma sintering from elemental powder mixture. Materials Letters. 2016;181:82-5.  https://doi.org/10.1016/j.matlet.2016.06.014
12.    Mohanty S, Maity T, Mukhopadhyay S, Sarkar S, Gurao N, Bhowmick S, et al. Powder metallurgical processing of equiatomic AlCoCrFeNi high entropy alloy: Microstructure and mechanical properties. Materials Science and Engineering: A. 2017;679:299-313.  https://doi.org/10.1016/j.msea.2016.09.062
13.    Ma Y, Jiang B, Li C, Wang Q, Dong C, Liaw PK, et al. The BCC/B2 morphologies in Al x NiCoFeCr high-entropy alloys. Metals. 2017;7(2):57.  https://doi.org/10.3390/met7020057
14.    Wang W-R, Wang W-L, Yeh J-W. Phases, microstructure and mechanical properties of AlxCoCrFeNi high-entropy alloys at elevated temperatures. Journal of Alloys and Compounds. 2014;589:143-52.  https://doi.org/10.1016/j.jallcom.2013.11.084
15.    Fu Z, Chen W, Wen H, Chen Z, Lavernia EJ. Effects of Co and sintering method on microstructure and mechanical behavior of a high-entropy Al0. 6NiFeCrCo alloy prepared by powder metallurgy. Journal of Alloys and Compounds. 2015;646:175-82.  https://doi.org/10.1016/j.jallcom.2015.04.238
16.    Chen Z, Chen W, Wu B, Cao X, Liu L, Fu Z. Effects of Co and Ti on microstructure and mechanical behavior of Al0. 75FeNiCrCo high entropy alloy prepared by mechanical alloying and spark plasma sintering. Materials Science and Engineering: A. 2015;648:217-24.  https://doi.org/10.1016/j.msea.2015.08.056
17.    Manzoni A, Daoud H, Völkl R, Glatzel U, Wanderka N. Phase separation in equiatomic AlCoCrFeNi high-entropy alloy. Ultramicroscopy. 2013;132:212-5.  https://doi.org/10.1016/j.ultramic.2012.12.015
18.    Wang F, Zhang Y. Effect of Co addition on crystal structure and mechanical properties of Ti0. 5CrFeNiAlCo high entropy alloy. Materials Science and Engineering: A. 2008;496(1-2):214-6.  https://doi.org/10.1016/j.msea.2008.05.020
19.    Lin C-M, Tsai H-L. Evolution of microstructure, hardness, and corrosion properties of high-entropy Al0. 5CoCrFeNi alloy. Intermetallics. 2011;19(3):288-94.  https://doi.org/10.1016/j.intermet.2010.10.008
20.    Ghanbariha M, Ketabchi M, Farvizi M. Investigation of alumina reinforcement effects on microstructure, hardness, and tribological behavior of AlCoCrFeNi high entropy alloy. Intermetallics. 2025;185:108915.  https://doi.org/10.1016/j.intermet.2025.108915
21.    Uporov S, Bykov V, Pryanichnikov S, Shubin A, Uporova N. Effect of synthesis route on structure and properties of AlCoCrFeNi high-entropy alloy. Intermetallics. 2017;83:1-8.  https://doi.org/10.1016/j.intermet.2016.12.003
22.    Han Z, Liang S, Yang J, Wei R, Zhang C. A superior combination of strength-ductility in CoCrFeNiMn high-entropy alloy induced by asymmetric rolling and subsequent annealing treatment. Materials Characterization. 2018;145:619-26.  https://doi.org/10.1016/j.matchar.2018.09.029
23.    Shahmir H, Nili-Ahmadabadi M, Shafiee A, Langdon TG. Effect of a minor titanium addition on the superplastic properties of a CoCrFeNiMn high-entropy alloy processed by high-pressure torsion. Materials Science and Engineering: A. 2018;718:468-76.  https://doi.org/10.1016/j.msea.2018.02.002
24.    Eleti R, Raju V, Veerasham M, Reddy S, Bhattacharjee P. Influence of strain on the formation of cold-rolling and grain growth textures of an equiatomic HfZrTiTaNb refractory high entropy alloy. Materials Characterization. 2018;136:286-92.  https://doi.org/10.1016/j.matchar.2017.12.034
25.    Han Z, Luan H, Liu X, Chen N, Li X, Shao Y, et al. Microstructures and mechanical properties of TixNbMoTaW refractory high-entropy alloys. Materials Science and Engineering: A. 2018;712:380-5.  https://doi.org/10.1016/j.msea.2017.12.004
26.    Senkov O, Wilks G, Miracle D, Chuang C, Liaw P. Refractory high-entropy alloys. Intermetallics. 2010;18(9):1758-65.  https://doi.org/10.1016/j.intermet.2010.05.014
27.    Rahmani M, Petrudi AM. Experimental and numerical optimization study of shock wave damping in aluminum panel sandwich. Fracture and Structural Integrity. 2021;15(55):88-109.  https://doi.org/10.3221/IGF-ESIS.55.07
28.    Saindane U, Soni S, Menghani J. Dry sliding behavior of carbon-based brake pad materials. International Journal of Engineering  Transactions B: Applications. 2021;34(11):2517-24.  https://doi.org/10.5829/ije.2021.34.11b.14
29.    Saindane U, Soni S, Menghani J. Friction and wear performance of brake Pad and optimization of manufacturing parameters using grey relational analysis. International Journal of Engineering, Transactions C: Aspects. 2022;35:552-9.  https://doi.org/10.5829/ije.2022.35.03c.07
30.    Saindane U, Soni S, Menghani J. Performance evaluation of brake pads developed using two different manufacturing methods. Materialwissenschaft und Werkstofftechnik. 2023;54(2):186-95.  https://doi.org/10.1002/mawe.202100407
31.    Jha P, Gupta P, Kumar D, Parkash O. Synthesis and characterization of Fe–ZrO2 metal matrix composites. Journal of Composite Materials. 2014;48(17):2107-15.  https://doi.org/10.1177/0021998313494915
32.    Ding J, Zhao N, Shi C, Du X, Li J. In situ formation of Cu–ZrO2 composites by chemical routes. Journal of alloys and compounds. 2006;425(1-2):390-4.  ttps://doi.org/10.1016/j.jallcom.2006.01.058
33.    Yu H, Hou Z, Guo X, Chen Y, Li J, Luo L, et al. Finite element analysis on flexural strength of Al2O3-ZrO2 composite ceramics with different proportions. Materials Science and Engineering: A. 2018;738:213-8.  https://doi.org/10.1016/j.msea.2018.05.075
34.    Hemanth J. Development and property evaluation of aluminum alloy reinforced with nano-ZrO2 metal matrix composites (NMMCs). Materials Science and Engineering: A. 2009;507(1-2):110-3.  https://doi.org/10.1016/j.msea.2008.11.039
35.    Grigor’eva T, Letsko A, Talako T, Tsybulya S, Vorsina I, Barinova A, et al. Producing Cu/ZrO2 composites by combining mechanical activation and self-propagating high-temperature synthesis. Combustion, Explosion, and Shock Waves. 2011;47(2):174-8.  https://doi.org/10.1134/S0010508211020055
36.    Chang C, Wang Y, Pei H, Lee C, Du X, Huang J. Microstructure and mechanical properties of nano-ZrO2 and nano-SiO2 particulate reinforced AZ31-Mg based composites fabricated by friction stir processing. Key Engineering Materials. 2007;351:114-9.  https://doi.org/10.4028/www.scientific.net/KEM.351.114
37.    Shackelford JF, Doremus RH. Ceramic and glass materials. JF Shackelford, RH Doremus. 2008:28-329.  
38.    Srivastava M, Srinivasan A, Grips VW. Influence of zirconia incorporation on the mechanical and chemical properties of Ni-Co alloys. American Journal of material science. 2011;1(2):113-22.  
39.    Ghanbariha M, Farvizi M, Ebadzadeh T. Microstructural development in nanostructured AlCoCrFeNi–ZrO2 high-entropy alloy composite prepared with mechanical alloying and spark plasma sintering methods. Materials Research Express. 2019;6(12):1265b5.  https://doi.org/10.1088/2053-1591/ab5fc9
40.    Ghanbariha M, Farvizi M, Ebadzadeh T, Samiyan AA. Effect of ZrO2 particles on the nanomechanical properties and wear behavior of AlCoCrFeNi–ZrO2 high entropy alloy composites. Wear. 2021;484:204032.  https://doi.org/10.1016/j.wear.2021.204032
41.    Zhou P, Xiao D, Yuan T. Microstructure, mechanical and corrosion properties of AlCoCrFeNi high-entropy alloy prepared by spark plasma sintering. 金属学报英文版. 2020;33(7):937-46.  https://doi.org/10.1007/s40195-019-00962-8 
42.    Farvizi M, Ebadzadeh T, Vaezi M, Yoon E, Kim Y, Kim H, et al. Microstructural characterization of HIP consolidated NiTi–nano Al2O3 composites. Journal of Alloys and Compounds. 2014;606:21-6.  https://doi.org/10.1016/j.jallcom.2014.03.184
43.    George EP, Raabe D, Ritchie RO. High-entropy alloys. Nature reviews materials. 2019;4(8):515-34.  https://doi.org/10.1038/s41578-019-0121-4
44.    Farvizi M, Bahamirian M, Faraji A, Kim H. Influence of ceramic reinforcement characteristics on the microstructure and wear behavior of NiTi matrix composites. Materialia. 2023;28:101726.  https://doi.org/10.1016/j.mtla.2023.101726
45.    Mirazimi J, Abachi P, Purazrang K. Spark plasma sintering of ultrafine YSZ reinforced Cu matrix functionally graded composite. Acta Metallurgica Sinica (English Letters). 2016;29(12):1169-76.  https://doi.org/10.1007/s40195-016-0512-0
46.    Baba NB, Davidson A, Muneer T. YSZ-reinforced Ni-P deposit: An effective condition for high particle incorporation and porosity level. Advanced Materials Research. 2011;214:412-7.  https://doi.org/10.4028/www.scientific.net/AMR.214.412
47.    Wang YS, Tan MJ, Chua BW, Bayraktar E. YSZ-Reinforced Mg-Based amorphous composites: processing, characterisation & corrosion. Advanced Materials Research. 2014;939:122-9.  https://doi.org/10.4028/www.scientific.net/AMR.939.122
48.    Yim D, Sathiyamoorthi P, Hong S-J, Kim HS. Fabrication and mechanical properties of TiC reinforced CoCrFeMnNi high-entropy alloy composite by water atomization and spark plasma sintering. Journal of Alloys and Compounds. 2019;781:389-96.  https://doi.org/10.1016/j.jallcom.2018.12.119
49.    Jiao W, Li T, Chang X, Lu Y, Yin G, Cao Z, et al. A novel Co-free Al0. 75CrFeNi eutectic high entropy alloy with superior mechanical properties. Journal of Alloys and Compounds. 2022;902:163814.  https://doi.org/10.1016/j.jallcom.2022.163814
International Journal of Engineering
Volume 39, Issue 10
TRANSACTIONS A: Basics
October 2026
Pages 2361-2370