Effect of nGO on Morphology, Mechanical Properties and Thermal Behavior of PLA/nGO Sheets Before and After Thermoforming: An Experimental Study

Document Type : Original Article

Authors

1 Department of Mechanical Engineering, Najafabad branch, Islamic Azad University, Najafabad, Iran

2 Modern Manufacturing Technologies Research Center, Najafabad Branch, Islamic Azad University, Najafabad, Iran

Abstract

Today, contrary to the benefits and advantages that the use of polymer materials has had for humans, the use of these materials has caused environmental problems for human life due to their non-degradability in nature. Therefore, the use of biodegradable polymers such as polylactic acid (PLA) is increasing. One of the main applications of plastic materials is the production of disposable containers. In this research, the thermoforming process of PLA sheets reinforced with graphene oxide nanoparticles (nGO) (0.4 and 1 wt.%) was investigated. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used to study the morphology of the samples before and after thermoforming. The mechanical properties before and after the thermoforming process were investigated by tensile test. The results showed that after the thermoforming process, the tensile strength of the sheets significantly increased, so that for the sample containing 1wt.% of nGO, the tensile strength increased by about 70%.  The results of the thickness distribution investigation showed that the lowest amount of thickness reduction, approximately 68%, is related to the sample containing 1 wt. % of nGO. The results of the DSC thermal test showed that the degree of crystallinity of the samples significantly decreased after thermoforming.

Keywords

Main Subjects

References

  1. Raquez, J.-M., Habibi, Y., Murariu, M. and Dubois, P., "Polylactide (pla)-based nanocomposites", Progress in Polymer Science, Vol. 38, No. 10-11, (2013), 1504-1542. https://doi.org/10.1016/j.progpolymsci.2013.05.014
  2. Armentano, I., Dottori, M., Fortunati, E., Mattioli, S. and Kenny, J., "Biodegradable polymer matrix nanocomposites for tissue engineering: A review", Polymer Degradation and Stability, Vol. 95, No. 11, (2010), 2126-2146. https://doi.org/10.1016/j.polymdegradstab.2010.06.007
  3. Liu, H. and Zhang, J., "Research progress in toughening modification of poly (lactic acid)", Journal of Polymer Science Part B: Polymer Physics, Vol. 49, No. 15, (2011), 1051-1083. https://doi.org/10.1002/polb.22283
  4. Stloukal, P., Pekařová, S., Kalendova, A., Mattausch, H., Laske, S., Holzer, C., Chitu, L., Bodner, S., Maier, G. and Slouf, M., "Kinetics and mechanism of the biodegradation of pla/clay nanocomposites during thermophilic phase of composting process", Waste Management, Vol. 42, (2015), 31-40. https://doi.org/10.1016/j.wasman.2015.04. 006
  5. Jadidi, H., Shahrajabian, H. and Moghri, M., "Using the mass method to produce pvc/clay nanocomposite foams: The effect of nano-clay and foaming conditions on density and cell size", Journal of Inorganic and Organometallic Polymers and Materials, Vol. 26, (2016), 881-888. https://doi.org/10.1007/s10904-016-0386-7
  6. Sheikh, K. and Shahrajabian, H., "Experimental study on mechanical, thermal and antibacterial properties of hybrid nanocomposites of pla/cnf/ag", International Journal of Engineering, Transactions B: Applications, Vol. 34, No. 2, (2021), 500-507. doi: 10.5829/IJE.2021.34.02B.23.
  7. Nian, L., Wang, M., Sun, X., Zeng, Y., Xie, Y., Cheng, S. and Cao, C., "Biodegradable active packaging: Components, preparation, and applications in the preservation of postharvest perishable fruits and vegetables", Critical Reviews in Food Science and Nutrition, (2022), 1-36. https://doi.org/10.1080/10408398.2022.2122924
  8. Vishal, K., Rajkumar, K., Sabarinathan, P. and Dhinakaran, V., "Mechanical and wear characteristics investigation on 3d printed silicon filled poly (lactic acid) biopolymer composite fabricated by fused deposition modeling", Silicon, Vol. 14, No. 15, (2022), 9379-9391. https://doi.org/10.1007/s12633-022-01712-9
  9. Stukhlyak, P., Buketov, A., Panin, S., Maruschak, P., Moroz, K., Poltaranin, M., Vukherer, T., Kornienko, L. and Lyukshin, B., "Structural fracture scales in shock-loaded epoxy composites", Physical Mesomechanics, Vol. 18, (2015), 58-74. https://doi.org/10.1134/S1029959915010075
  10. Mosalman, S., Rashahmadi, S. and Hasanzadeh, R., "The effect of tio2 nanoparticles on mechanical properties of poly methyl methacrylate nanocomposites (research note)", International Journal of Engineering, Transactions B: Applications, Vol. 30, No. 5, (2017), 807-813. doi: 10.5829/idosi.ije.2017.30.05b.22.
  11. Mohammadnia, M., Derakhshani, E. and Naghizadeh, A., "Defluoridation of aqueous solution by graphene and graphene oxide nanoparticles: Thermodynamic and isotherm studies", Iranian Journal of Chemistry and Chemical Engineering, Vol. 39, No. 1, (2020), 67-77. doi: 10.30492/IJCCE.2020.33341.
  12. Keshavarz, M.R. and Hassanajili, S., "Effect of graphene oxide reduction with l-ascorbic acid on electrical conductivity and mechanical properties of graphene oxide-epoxy nanocomposites", Iranian Journal of Chemistry and Chemical Engineering, Vol. 40, No. 3, (2021), 731-742. doi: 10.30492/IJCCE.2020.38254.
  13. Liu, L., Zhang, J., Zhao, J. and Liu, F., "Mechanical properties of graphene oxides", Nanoscale, Vol. 4, No. 19, (2012), 5910-5916. https://doi.org/10.1039/C2NR31164J
  14. Moslehi Niasar, M., Molaei, M. and Aghaei, A., "Electromagnetic wave absorption properties of barium ferrite/reduced graphene oxide nanocomposites", International Journal of Engineering, Transactions C: Aspects, Vol. 34, No. 6, (2021), 1503-1511. doi: 10.5829/IJE.2021.34.06C.14.
  15. Gao, W., "The chemistry of graphene oxide", Graphene oxide: Reduction Recipes, Spectroscopy, and Applications, Vol., No., (2015), 61-95. https://doi.org/10.1007/978-3-319-15500-5_3
  16. Sharifiana, M. and Shahrajabian, H., "The study of mechanical, thermal, and antibacterial properties of pla/graphene oxide/tio2 hybrid nanocomposites", Iranian Journal of Chemistry and Chemical Engineering, Vol. 41, No. 3, (2022), 799-807. doi: 10.30492/IJCCE.2021.128785.4173.
  17. Fredi, G., Karimi Jafari, M., Dorigato, A., Bikiaris, D.N. and Pegoretti, A., "Improving the thermomechanical properties of poly (lactic acid) via reduced graphene oxide and bioderived poly (decamethylene 2, 5-furandicarboxylate)", Materials, Vol. 15, No. 4, (2022), 1316. https://doi.org/10.3390/ma15041316
  18. Khammassi, S., Tarfaoui, M., Škrlová, K., Měřínská, D., Plachá, D. and Erchiqui, F., "Poly (lactic acid)(pla)-based nanocomposites: Impact of vermiculite, silver, and graphene oxide on thermal stability, isothermal crystallization, and local mechanical behavior", Journal of Composites Science, Vol. 6, No. 4, (2022), 112. https://doi.org/10.3390/jcs6040112
  19. Banús, N., Boada, I., Xiberta, P., Toldrà, P. and Bustins, N., "Deep learning for the quality control of thermoforming food packages", Scientific Reports, Vol. 11, No. 1, (2021), 21887. https://doi.org/10.1038/s41598-021-01254-x
  20. Ghorbani, S. and Matochi, A., "Thermoforming and its applications, a review", Basparesh, Vol. 10, No. 2, (2020), 37-47. doi: 10.22063/BASPARESH.2020.2539.1483.
  21. Choi, J., Han, C., Cho, S., Kim, K., Ahn, J., Del Orbe, D., Cho, I., Zhao, Z.-J., Oh, Y.S. and Hong, H., "Customizable, conformal, and stretchable 3d electronics via predistorted pattern generation and thermoforming", Science Advances, Vol. 7, No. 42, (2021), eabj0694. doi: 10.1126/sciadv.abj0694.
  22. Wittmann, L.-M. and Drummer, D., "Multilayer sheets for thermoforming non thermoformable polymers", Journal of Plastic Film & Sheeting, Vol. 38, No. 2, (2022), 225-244. https://doi.org/10.1177/87560879211037387
  23. Albilali, A.T., Baras, B.H. and Aldosari, M.A., "Evaluation of mechanical properties of different thermoplastic orthodontic retainer materials after thermoforming and thermocycling", Polymers, Vol. 15, No. 7, (2023), 1610. https://doi.org/10.3390/polym15071610
  24. Atmani, O., Abbès, F., Li, Y., Batkam, S. and Abbès, B., "Experimental and numerical investigation of the effects of sheet material, plug-assist tool material, and process conditions on the mechanical pre-stretching stage of plug-assist thermoforming", The International Journal of Advanced Manufacturing Technology, Vol. 122, No. 7-8, (2022), 3217-3234. https://doi.org/10.1007/s00170-022-10125-2
  25. Wei, H., "Optimisation on thermoforming of biodegradable poly (lactic acid)(pla) by numerical modelling", Polymers, Vol. 13, No. 4, (2021), 654. https://doi.org/10.3390/polym13040654
  26. O’Connor, C., Menary, G., Martin, P. and McConville, E., "Finite element analysis of the thermoforming of polypropylene", International Journal of Material Forming, Vol. 1, No. Suppl 1, (2008), 779-782. https://doi.org/10.1007/s12289-008-0291-x
  27. Ghobadnam, M., Mosaddegh, P., Rezaei Rejani, M., Amirabadi, H. and Ghaei, A., "Numerical and experimental analysis of hips sheets in thermoforming process", The International Journal of Advanced Manufacturing Technology, Vol. 76, (2015), 1079-1089. https://doi.org/10.1007/s00170-014-6329-y
  28. Turan, E., Konuşkan, Y., Yıldırım, N., Tuncalp, D., Inan, M., Yasin, O., Turan, B. and Kerimoğlu, V., "Digital twin modelling for optimizing the material consumption: A case study on sustainability improvement of thermoforming process", Sustainable Computing: Informatics and Systems, Vol. 35, (2022), 100655. https://doi.org/10.1016/j.suscom.2022.100655
  29. Gonon, H., Srisa, A., Promhuad, K., Chonhenchob, V., Bumbudsanpharoke, N., Jarupan, L. and Harnkarnsujarit, N., "Pla thermoformed trays incorporated with cinnamaldehyde and carvacrol as active biodegradable bakery packaging", Food Packaging and Shelf Life, Vol. 38, (2023), 101123. https://doi.org/10.1016/j.fpsl.2023.101123
  30. Sorimpuk, N., Choong, W. and Chua, B., "Design of thermoformable three dimensional-printed pla cast for fractured wrist", in IOP Conference Series: Materials Science and Engineering, IOP Publishing. Vol. 1217, (2022), 012002.
  31. Swetha, T.A., Bora, A., Mohanrasu, K., Balaji, P., Raja, R., Ponnuchamy, K., Muthusamy, G. and Arun, A., "A comprehensive review on polylactic acid (pla)–synthesis, processing and application in food packaging", International Journal of Biological Macromolecules, (2023), 123715. https://doi.org/10.1016/j.ijbiomac.2023.123715
  32. Barletta, M. and Puopolo, M., "Thermoforming of compostable pla/pbs blends reinforced with highly hygroscopic calcium carbonate", Journal of Manufacturing Processes, Vol. 56, (2020), 1185-1192. https://doi.org/10.1016/j.jmapro.2020.06.008
International Journal of Engineering
Volume 36, Issue 9
TRANSACTIONS C: Aspects
September 2023
Pages 1695-1703

Files

Share

How to cite

Statistics