Influence of Water Cooling on Orthogonal Cutting Process of Ti-6Al-4V Using Smooth-Particle Hydrodynamics Method

Document Type : Original Article

Authors

Department of mechanical Engineering, Yazd University, Yazd, Iran

Abstract

Temperature control during the cutting process with different parameters such as cutting velocity and applying water cooling is essential to decrease the cutting force, increase the life of the cutting tool and decrease the machined surface temperature of work-piece. In this research, the temperature of machined surface and the chip-tool interface in orthogonal cutting process of Ti-6Al-4V were investigated using smooth particle hydrodynamics (SPH) method. The effects of cooling with different speeds and temperatures of water flow on the temperature of these surfaces were studied. The non-cooling model is validated using experimental results. According to the results, a water flow with speed of 0.25 m/s at 20°C temperature causes a significant decreasing in the cutting force and the temperature on machined surface and chip-tool interface.

Keywords


1. Rajeeva D., Dinakaranb D., Kanthavelkumaran N., Austind N.
"Predictions of Tool Wear in Hard Turning of AISI4140 Steel
through Artificial Neural Network, Fuzzy Logic and Regression
Models" International Journal of Engineering-Transactions
A: Basic,  Vol. 31, (2018), 32-37  
2. Edema F., Balogun V. A. "Energy Efficiency Analyses of
Toolpaths in a Pocket Milling Process" International Journal of
Engineering-Transactions A: Basic, Vol. 31, (2018), 847-855  
3. Balogun V. A., Edemb I. F. " Optimum Swept Angle Estimation
based on the Specific Cutting Energy in MillingAISI 1045 Steel
Alloy" International Journal of Engineering-Transactions A:
Basic, Vol. 30, (2017), 591-596  
4. Patel S. S., Prajapatib J. M. " Experimental Investigation of
Surface Roughness and Kerf Width During Machining of
Blanking Die Material on Wire Electric Discharge Machine"
International Journal of Engineering-Transactions A: Basic,
Vol. 31, (2018), 1760-1766   
5. Safari M., Joudaki J., Emadi M., "Surface Quality in Dry
Machining of 55Cr3 Steel Bars." International Journal of ISSI,
Vol. 15, (2018), 33-39 
6. Kline WA, Devor RE, Lindberg JR. "The Prediction Of Cutting
Forces In End Milling With Application To Cornering Cuts."
International Journal of Machine Tool Design and Research,
Vol. 22, (1982), 7-22 
7. Tsai CL. "Analysis and prediction of cutting forces in end
milling by means of a geometrical model." International
Journal of Advanced Manufacturing Technology, Vol. 31,
(2007), 888–896 
8. Li HZ, Li XP. "Milling force prediction using a dynamic shear 
length model." International Journal of Machine Tools and
Manufacture, Vol. 42, (2002), 277–86 
9. Madaj M, Píška M. "On the SPH orthogonal cutting simulation
of A2024-T351 alloy." Procedia Cirp., Vol. 8, (2013), 152–157 
10. Limido J, Espinosa C, Salau M, Lacome JL. SPH method
applied to high speed cutting modelling. Internatnonal Journal
Mechanical Sciences. Vol. 85, (2016), 2377–2388 
11. Lia B., Wang Y., Li H., You H., “Modelling and Numerical
Simulation of Cutting Stress in End Milling of Titanium Alloy
using Carbide Coated Tool“, International Journal of
Engineering-Transactions A: Basic, Vol. 28, (2015), 10901098
12. Heinstein M, Segalman D. Simulation of Orthogonal Cutting
with Smooth Particle Hydrodynamics. Report, Sandia National
Laboratories,  USA, September 1997.  
13. Stone CM, Wellman GW, Krieg RD. A vectorized elastic/plastic 
power law hardening material model including luders strain.
Report, Sandia National Laboratories, USA, March1990.  
14. Villumsen MF, Fauerholdt TG. Simulation of Metal Cutting
using Smoothed Particle Hydrodynamics. 7th ed. LS-DYNA
Anwenderforum, 2008.  
15. Lu J, Chen J, Fang Q, Liu B, Liu Y, Jin T. "Finite element
simulation for Ti-6Al-4V alloy deformation near the exit of
orthogonal cutting." International Journal of Advanced
Manufacturing Technology, Vol. 85, (2016), 2377–2388 
16. Cotterell M, Ares E, Yanes J, López F, Hernandez P, Peláez G.
"Temperature and strain measurement during chip formation in
orthogonal cutting conditions applied to Ti-6Al-4V." Procedia
Engineering, Vol. 63, (2013), 922–930 
17. Kuczmaszewski J, Zagórski I, Zgórniak P. "Thermographic
study of chip temperature in high-speed dry milling magnesium
alloys." Management and Production Engineering Review,
Vol. 7, (2016), 86–92 
18. Fang F.Z., Lee L.C. LXD. "Mean Flank Temperature
Measurement in High Speed Dry Cutting." Journal of Materials
Processing Technology, 2005;167:119–23. Vol. 118, (2001),
301–308 
19. O ’ Sullivan D. CM. "Temperature measurement in single point
turning", Journal of Materials Processing Technology,Vol.
118, (2001), 301–308 
20. Franz Obermair SP, Klammer G. "high speed minimum quantity
lubrication machining of magnesium." In: Proceedings of the 6th
International Conference Magnesium Alloys and Their
Applications. Germany, 2005. 881–887. Wiley 
21. Jeong-Du, Kim K-BL. "Surface Roughness Evaluation in DryCutting
of Magnesium Alloy by Air Pressure Coolant."
Engineering. Vol. 2, (2010), 788–792 
22. Heigel JC, Whitenton E, Lane B, Donmez MA, Madhavan V.
Infrared Measurement of the Temperature at the Tool-Chip
Interface While Machining Ti-6Al-4V. Journal of Materials
Processing Technology, Vol. 243, (2017), 123-130 
23. Monaghan JJ. "Smoothed Particle Hydrodynamics." Annual
Review of Astronomy and Astrophysics, Vol. 30, (1992), 543–
574 
24. Fadaei-Kermani E., Shojaee S., Memarzadeh R. "Numerical
Simulation of Seepage Flow through Dam Foundation Using
Smooth Particle Hydrodynamics Method" International
Journal of Engineering-Transactions A: Basic Vol. 32, (2019),
484-488 
25. Benz W, Asphaug E. "Simulations of brittle solids using smooth
particle hydrodynamics." Computer Physics Communications,  
Vol. 87, (1995), 253–265 
26. Gray JP, Monaghan JJ, Swift RP. SPH elastic dynamics.
Computer Methods in Applied Mechanics and Engineering, 
Vol. 190, (2001), 6641–6662
27. Hiermaier S, Konke D, Stilp AJJ, Thoma K, Könke D. 
"Computational simulation of the hypervelocity impact of al-
spheres on thin plates of different materials".  International
Journal of Impact Engineering, Vol. 20, (1997), 363–374 
28. M.H. Farahani and N. Amanifard, S.M. Hosseini, "a highvelocity
impact simulation using sphprojection method",
International Journal of Engineering-Transactions A: Basic
Vol. 22, (2009), 359-368 
29. Hoseinpour B., Amanifard N., Basti A., " Simulation of Cold
Rolling Process Using Smoothed Particle Hydrodynamics
(SPH)", International Journal of Engineering-Transactions A:
Basic Vol. 26, (2013), page no. 515-522 
30. Zhang Y, Outeiro JC, Mabrouki T. "On the selection of JohnsonCook constitutive model parameters for Ti-6Al-4V using three types of numerical models of orthogonal cutting" Procedia Cirp.
Vol. 31, (2015), 112–117