Effect of Wire Pitch on Capacity of Single Staggered Wire and Tube Heat Exchanger Using Computational Fluid Dynamic Simulation

Document Type: Original Article

Authors

Department of Mechanical Engineering, Universitas Negeri Surabaya, East Java, Indonesia

Abstract

Single staggered is a design development of normal wire and tube heat exchanger that wires are welded with staggered configuration on two sides. Capacity of wire and tube heat exchanger is the ability of the heat exchanger to release heat. The objective of this study is to analyse the effect of wire pitch (pw) on capacity of single staggered wire and tube heat exchanger. The research method uses Computational Fluid Dynamic (CFD) simulation by ANSYS Fluent to analyse heat transfer of wire and tube; also to analyse airflow at surface the wire and tube. The simulation is experimentally validated by measuring temperatures at some points of wire and tube. Based on results, temperature contours increasing capacity of heat exchanger depend on smaller wire pitch that the highest value is 72.02 W at pw 7 mm. The reason is smaller wire pitch increases area of convection heat transfer surface. Whereas, airflow patterns show air move slowly at the wire and tube surface and flow with free convection. This study contributes new design of wire and tube heat exchanger with CFD and it can be applied to improve the performance of this heat exchanger in refrigeration system and other applications.

Keywords


  1. Omer, A., “Heat Exchanger Technology and Applications in Heat Exchanger Engineering”, Advances in Nanoscience and Nanotechnology, Vol. 3. (2019), 1-3. Doi: 10.33140/ann.03.01.01
  2. Topcuoglu, K., “Trombe Wall Application with Heat Storage Tank”, Civil Engineering Journal, Vol. 5, No. 7, (2019), 1477-1489. Doi: 10.28991/cej-2019-03091346
  3. Zhang, W., Yang, X., Wang, T., Peng, X., Wang, X., “Experimental Study of a Gas Engine-diven Heat Pump System for Space Heating and Cooling”, Civil Engineering Journal, Vol. 5, No. 10, (2019), 2282-2295. Doi: 10.28991/cej-2019-03091411
  4. Kumra, A., Rawal, N., Samui, P., “Prediction of Heat Transfer Rate of a Wire-on-Tube Type Heat Exchanger: An Artificial Intelligence Approach”, Procedia Engineering, No. 64, (2013), 74-83. Doi: 10.1016/j.proeng.2013.09.078
  5. Bansal, P.K., and Chin, T.C., “Modelling and Optimisation of Wire and Tube Condenser”, International Journal of Refrigeration, No. 26, (2003), 601-603. Doi: 10.1016/s0140-7007(02)00044-0
  6. Ahmed A. M. Saleh, “Correlation of Overall Heat Transfer Coefficient in Three Zones of Wire and Tube Condenser”, Journal of Mechanical Engineering Research and Deveopment (JMERD), Vol. 42 No. 1, (2019), 96-103. Doi: 10.26480/jmerd.01.2019.96.103
  7. Arsana, I. M., Budhikardjono, K., Susianto., Altway, A., “Optimization of The Single Staggered Wire and Tube Heat Exchanger”, MATEC Web of Conference, No. 58, (2016).  Doi: 10.1051/matecconf/20165801017
  8. Arsana, I Made., Budhikardjono, Kusno., Susianto., and Altway, Ali., “Modelling of The Single Staggered Wire and Tube Heat Exchanger”, International Journal of Applied Engineering Research, Vol. 11, No. 8, (2016), 5591-5599.
  9. Gonul, A., Agra, O., Atayilmaz, O., Demir, H., Sevendir, Kemal, M., Teke, “Experimental and Numerical Investigation of Air Side Forced Convection on Wire-on-Tube Condensers”, International Journal of Thermal Science, Vol. 151, (2020), 106241. Doi: 10.1016/j.ijthermalsci.2019.106241
  10. Sengupta, A. R., Gupta, R., Biswas, A., “Computational Fluid Dynamic Analysis of Stove Systems for Cooking and Drying of Muga Silk”, Emerging Science Journal, Vol. 3, No. 5 (2019), 285-292. Doi: 10.28991/esj-2019-01191
  11. Teja, S.T.G. Krishna., Karthikeyan, C. P., and Kumar, M. B. Shyam., “Investigation of Radiative Cooling Using a Photonic Composite Material for Water Harvesting”, International Journal of Engineering, Transaction A: Basic, Vol. 30, No. 10, (2017), 1573-1582. Doi:  10.5829/ije.2017.30.10a.19
  12. Davarnejad, R., Barati, S., Zakeri, M., “Simulation of Comvective Heat Transfer of a Nanofluid in a Circular Cross-section”, International Journal of Engineering, Transaction C: Aspects, Vol. 26, No. 6, (2013), 571-576. Doi: 10.5829/idosi.ije.2013.26.06c.02
  13. Djodikusumo, I., Diasta, I.N., Awaluddin, I.S., “Geometric Modelling of a Propeller Turbine Runner Using ANSYS BladeGen Meshing Using ANSYS TurboGrid and Fluid Dynamic Simulation Using ANSYS Fluent”, Trans Tech Publications, Ltd., Vol. 842, (2016), 164-177. Doi: 0.4028/www.scientific.net/amm.842.164
  14. Patel, S.D., Parmar, R.R., Prajapati, V.M., “CFD Analysis of Shell and Tube Heat Exchanger”, International Research Journal of Engineering and Technology (IRJET), Vol. 2, (2015), 2231-2235. Doi: 10.23883/ijrter.2017.3386.jcalx
  15. Vazifeshenas, Y., Delavar, M.A., “Investigation of Thermo-hydraulic Performance of Circular Tube Fitted with Center-cleared Twisted Tape Using CFD Modeling”, International Journal of Engineering, Transaction C: Aspects, Vol. 28, No. 3, (2015), 476-482. Doi: 10.5829/idosi.ije.2015.28.03c.19
  16. Barzegar, M.H., Fallahiyekta, M., “Increasing Thermal Efficiency of Double Tube Heat Exchangers by Using Nano Hybrid”, Emerging Journal Science, Vol. 2, No. 1, (2018), 11-19. Doi: 10.28991/esj-2018-01122